Author Topic: Nem megfeleloek az epuletek  (Read 8924 times)

Offline eckertomi

  • Newbie
  • *
  • Posts: 4
Nem megfeleloek az epuletek
« on: September 20, 2017, 21:02:13 PM »
Hello,

Ma megvettem az LHBP Sceneryt , de igy jelenik meg. A .dll fajlt engedelyeztem inditaskor. Semmi hiba uzenetet nem irt ki telepites es futtatas kozben.

Offline m814

  • Administrator
  • Hero Member
  • *****
  • Posts: 1.459
Re: Nem megfeleloek az epuletek
« Reply #1 on: September 20, 2017, 21:39:05 PM »
Szia!
FSX Service pack 2 telepítve van?

Lima Hotel Simulations - Flight Simulator scenery design for Hungary
By NASA: MOS-8500 0,985@1,023Mhz, VIC-II 320*200 16 colour,65,536 Kbyte,Datasette 300

Offline eckertomi

  • Newbie
  • *
  • Posts: 4
Re: Nem megfeleloek az epuletek
« Reply #2 on: September 20, 2017, 23:36:47 PM »
FSX Gold editionom van Acclereation patchel. Nem tudom, hogy abban benne van-e az SP2. Sok addon airportom van de eddig egyikel sem volt problema.

Offline eckertomi

  • Newbie
  • *
  • Posts: 4
Re: Nem megfeleloek az epuletek
« Reply #3 on: September 22, 2017, 16:23:40 PM »
Valaki? Otlet?  :-[

Offline marci1229

  • Valued Customer
  • Full Member
  • *****
  • Posts: 44
  • Marci1229
Re: Nem megfeleloek az epuletek
« Reply #4 on: February 12, 2018, 22:21:22 PM »
Question: I cannot see the buildings. The jetways are there, but the terminals and some other stuff is missing.

This means that the object placer dll is not working. This dll is used to place different objects into the sim.

Step 1: Did you get any error message during the installation or when your simulator was loading?
If yes please check the error message explanations below. If you can not find that particular message please open a new topic in the forum.

If not,

Step 2: Open a flight, and take a look at the "Add-ons" menu in the top menu bar. Do you see an option that says "LHSimulations"?

If the menu option is there, and you still can not see any building.

If you are using GSX, when you load GSX the objects will disappear. Please make sure you are using GSX's latest version, this error was solved in the recent version only.

If you renamed the title of the scenery in your scenery library please change it back to LHS_LHBP_X . We builded in an option to check if the scenery was activated. It turned out a lot of user rename the scenery title. We will correct this bug soon.

If you do not use GSX or the object disappeared from the beginning of the flight please contact us directly, open a new topic in the support forum.

If you do not see the menu option at all:

Please check if in your [FSX/Prepar3D root]\Modules folder a file called LHBP_objectPlacer.dll is present. If not try to re-run the following [FSX root]\Addon scenery\LHS_LHBP_X\LHSactivator.exe . If there is a problem this program should throw an error message. If you get an error message find the error description here below and proceed accordingly. If everything is okay then a message will come up "LHSimulations scenery activation is successful", in your Modules folder an LHBP_objectPlacer.dll should be present now. If it is not present contact us, open a new topic on the forum.

If the dll is present in your Modules folder than find and check your dll.xml file.
You can find the file if you copy and paste this into your Windows Explorer adress bar.
Code: [Select]
%APPDATA%\Microsoft\FSX or Prepar3D

Try opening it in a webbrowser, make sure it does not throw and error. Try and see if you can find this part in there (usually at the end of the file):

Code: [Select]
<Launch.Addon>
        <Name>LHBP objectPlacer</Name>
        <Disabled>False</Disabled>
        <Path>Modules\LHBP_objectPlacer.dll</Path>
</Launch.Addon>

If you could find the lines above in your dll.xml:

You may try to move this section to the top of the dll.xml file after the <Launch.ManualLoad>False</Launch.ManualLoad> line. If you have never edited your dll.xml we recommend to use FSXML program created by flight1 . You can download it here : www.flight1.com/view.asp?page=library
Save you dll.xml and re-start your FSX. If you still have a problem please contact us here at the forum, open a new topic.

If you could not find these lines in your dll.xml

Maybe you ran the installer without Administrator rights and it could not change your dll.xml. You may add the lines above manually in your dll.xml or you could use SXML program created by flight1 . You can download it here : www.flight1.com/view.asp?page=library
Save you dll.xml and re-start your FSX. If you still have a problem please contact us here at the forum, open a new topic.

Offline marci1229

  • Valued Customer
  • Full Member
  • *****
  • Posts: 44
  • Marci1229
Re: Nem megfeleloek az epuletek
« Reply #5 on: February 12, 2018, 22:24:47 PM »
Kérdés: Nem látom az épületeket. A jetways ott vannak, de a terminálok és más dolgok hiányoznak.

Ez azt jelenti, hogy az object placer dll nem működik. Ez a dll különböző objektumokat helyez a SIM-be.

1. lépés: Hiba történt a telepítés vagy a szimulátor betöltése során?
Ha igen, kérjük, ellenőrizze az alábbi hibaüzeneteket. Ha nem találja ezt az üzenetet, kérjük, nyisson meg egy új témát a fórumban.

Ha nem,

2. lépés: Nyissa meg a járatot, és nézze meg a "Kiegészítők" menüt a felső menüsorban. Látsz egy opciót, amely "LHSimuláció" -ot mond?

Ha a menü opció van, és még mindig nem látsz egy épületet.

Ha GSX-t használ, a GSX betöltésekor az objektumok eltűnnek. Győződjön meg arról, hogy a GSX legfrissebb verzióját használja, ezt a hibát csak a legutóbbi verzióban oldotta meg.

Ha átnevezi a táj címét a tájfedvénykönyvtárban, cserélje vissza LHS_LHBP_X címre. Beépítettük a lehetőséget, hogy ellenőrizzük, hogy a táj be van-e kapcsolva. Kiderült, hogy sok felhasználó átnevezi a táj címét. Hamarosan kijavítjuk ezt a hibát.

Ha nem használja a GSX-t, vagy az objektum eltűnik a járat kezdetétől, kérjük, forduljon hozzánk közvetlenül, és nyisson meg egy új témát a támogatási fórumban.

Ha egyáltalán nem látja a menüopciót:

Ellenőrizze, hogy a [FSX / Prepar3D root] \ Modules mappában van-e LHBP_objectPlacer.dll nevű fájl. Ha nem próbálja újra végrehajtani a következő [FSX root] \ Addon scenery \ LHS_LHBP_X \ LHSactivator.exe fájlt. Ha probléma merül fel, a programnak hibaüzenetet kell küldenie. Ha hibaüzenet jelenik meg, keresse meg az alábbi hibakövetelményt, és ennek megfelelően járjon el. Ha minden rendben van, akkor megjelenik egy üzenet: "LHSimulations scenery activation is successful", a Modules mappában egy LHBP_objectPlacer.dll kell jelen lenni. Ha nem jelen van, forduljon hozzánk, nyiss egy új témát a fórumon.

Ha a dll a Modules mappában van, akkor megtalálja és ellenőrizze a dll.xml fájlt.
Megtalálhatja a fájlt, ha másolja és illessze be a Windows Intéző címsorába.
Kód: [Kiválaszt]
% APPDATA% \ Microsoft \ FSX vagy Prepar3D

Próbálja megnyitni egy webbrowserben, győződjön meg róla, hogy nem dobja el és hiba. Próbáld meg megnézni, hogy megtalálod-e ezt a részt (általában a fájl végén):

Kód: [Kiválaszt]
<Launch.Addon>
        <Név> LHBP objectPlacer </ Name>
        <Disabled> False </Disabled>
        <Útvonal> Modules \ LHBP_objectPlacer.dll </ útvonal>
</Launch.Addon>


Ha egy Modul mappában van, találja és ellenőrizze a dll.xml fájlt.
Megtalálhat egy fájlt, ha másolja és illessze egy Windows Intéző címsorába.
Kód: [Kiválaszt]
% APPDATA% \ Microsoft \ FSX vagy Prepar3D



Ha megtalálja a fenti sorokat a dll.xml-ben:

Megpróbálhatja áthelyezni ezt a szakaszt a dll.xml fájl tetejére a <Launch.ManualLoad> False </Launch.ManualLoad> sor után. Ha még soha nem szerkesztette a dll.xml-et, akkor javasoljuk, hogy használja a flight1 által létrehozott FSXML programot. Letöltheti itt: www.flight1.com/view.asp?page=library
Mentse el a dll.xml-et, és indítsa újra az FSX-t. Ha még mindig problémád van, kérjük, vegye fel velünk a kapcsolatot a fórumon, nyisson meg egy új témát.

Ha nem találod ezeket a sorokat a dll.xml-ben

Lehet, hogy a telepítőt adminisztrátori jogok nélkül futtatta, és nem tudta megváltoztatni a dll.xml fájlt. A fenti sorokat manuálisan hozzáadhatja a dll.xml fájlba, vagy használhatja a flight1 által létrehozott SXML programot. Letöltheti itt: www.flight1.com/view.asp?page=library
Mentse el a dll.xml-et, és indítsa újra az FSX-t. Ha még mindig problémád van, kérjük, vegye fel velünk a kapcsolatot a fórumon, nyisson meg egy új témát.
« Last Edit: February 12, 2018, 22:29:19 PM by marci1229 »

Offline tamasgondos

  • Newbie
  • *
  • Posts: 2
Re: Nem megfeleloek az epuletek
« Reply #6 on: June 12, 2019, 23:02:46 PM »
Sziasztok,

P3DV4.4-hez vásároltam meg az LHBP sceneryt,de az épületeknek csak a helye látszódik az is feketével.A dll fájl a modul mappában,rendszergazdaként telepítve,hibátlanul lefutott a telepítés.Elindítva egy repülést,a felső menüsor Options->Addons-ban meg kellene jelennie?A főmenüben az add on sceneryk között megvan.Köszi

Offline tamasgondos

  • Newbie
  • *
  • Posts: 2
Re: Nem megfeleloek az epuletek
« Reply #7 on: June 13, 2019, 06:52:36 AM »
Itt a dll.xml illetve képek.

<SimBase.Document Type="Launch" version="1,0">
  <Descr>Launch</Descr>
  <Filename>dll.xml</Filename>
  <Disabled>False</Disabled>
  <Launch.ManualLoad>False</Launch.ManualLoad>

<Launch.Addon>
  <Name>LHBP_objectPlacer64.dll</Name>
  <Disabled>False</Disabled>
  <Launch.ManualLoad>False</Launch.ManualLoad>
  <Path>C:\Gamez\Prepar3D\Modules\LHBP_objectPlacer64.dll</Path>
 </Launch.Addon>


 
  <Launch.Addon>
    <Name>FSUIPC 5</Name>
    <Disabled>False</Disabled>
    <Path>C:\Gamez\Prepar3D\Modules\FSUIPC5.dll</Path>
   </Launch.Addon>

   <Launch.Addon>
      <Name>Carenavigraph</Name>
      <Disabled>False</Disabled>
      <Path>.\Carenavigraph.dll</Path>
   </Launch.Addon>

</SimBase.Document>
<Launch.Addon>
    <Name>carenavigraph</Name>
    <Disabled>False</Disabled>
    <Path>.\carenavigraph.dll</Path>
  </Launch.Addon>

   <Launch.Addon>
      <Name>Carenavigraph</Name>
      <Disabled>False</Disabled>
      <Path>.\Carenavigraph.dll</Path>
   </Launch.Addon>

</SimBase.Document>